Friday, August 17, 2018

Anytek Waterproof P3 Fingerprint Padlock User Manual

Anytek Waterproof P3 Fingerprint Padlock User Manual







USB Interface:

The product is charged by USB. Please fully charge the 

product for the first time.

Components:



1.USB Port             2.Fingerprint Reader

3.LED Light            4. Lock Beam



Anytek Waterproof P3 Fingerprint Padlock Operations:

*It can be unlocked by any fingerprint when there’s no fingerprint recorded. In case of mess up in future and cannot find the administrator to unlock the lock, please set the administrator fingerprint at the beginning.

It can be recorded 10 different fingerprints in total, the earliest 2 fingerprints are the administrators. When you set well the fingerprint, the other unrecorded fingerprints cannot be unlocked. When you recorded the first administrator fingerprint, the subsequent entry of a new fingerprint requires the administrator's fingerprint authorization.(the 1st and 2nd fingerprints are the administrators by default).

P3 Fingerprint Padlock Record the fingerprint and the instruction of LED indicator status

Anytek P3 Fingerprint Padlock



P3 Fingerprint Padlock First time to record the fingerprint and the instruction of LED indicator status.
1. When first time to record the fingerprint, long press the sensor for 3 seconds, release the finger when you saw the blue indicator light on, and the green indicator light flashes.
2.When the green indicator light flashes, please start to collect the fingerprint. After ten times successful fingerprint collection, the green indicator light will remain on indicates that the current fingerprint collection is successful.(A. When you collect the fingerprint every time, the blue indicator light will on and that means collect successful. B. Please use the same finger to complete the 10 times fingerprint collections, otherwise it will not be sensitive when you unlocking the lock)
Note:
1.If you long press the sensor over than 3 seconds but you still not yet released it when the blue indicator light on, then the red indicator light will on, for the moment, it will enter into the fingerprint deleting mode, when the administrator fingerprint touch the sensor again, it will delete all the fingerprints.
2.When the green indicator light flashes but you didn’t collect the fingerprint in time, when the green indicator light off that means it already quitted from the fingerprint recording mode, you need to operate it again.

P3 Fingerprint Padlock Recording the 2nd to the 10th fingerprint and the LED indicator status instruction.
1.Long press the sensor for 3 seconds, release the finger till the blue indicator light on shortly, then the blue indicator light will always on.
2.When the blue indicator light remained on that means it needs the administrator’s authorize, for this moment, the administrator fingerprints need to be pressed on the sensor, once the administrator fingerprint authorization successfully, the green indicator light will flash.
3.When the green indicator light flashes, please start to collect the fingerprint. After ten times successful fingerprint collection, the green indicator light will remain on indicates that the current fingerprint collection is successful.(A. When you collect the fingerprint every time, the blue indicator light will on and that means collect successful. B. Please use the same finger to complete the 10 times fingerprint collections, otherwise it will not be sensitive when you unlocking the lock)
Note:
1.If you long press the sensor over than 3 seconds but you still not yet released it when the blue indicator light on, then the red indicator light will on, for the moment, it will enter into the fingerprint deleting mode, when the administrator fingerprint touch the sensor again, it will delete all the fingerprints.
When the Non-administrator’s fingerprint touch the sensor, the red indicator will on.
2.When the blue indicator remains on but the administrator fingerprint is unable to authorize it in time, it will lead the indicator light off that means it already quitted from the fingerprint recording mode, you need to operate it again.
3.When the green indicator light flashes but you didn’t record the fingerprint in time, when the green indicator light off that means it already quitted from the fingerprint recording mode, you need to operate it again.
4.The second fingerprint was defaulted to be the 2nd administrator. The recording method from 3rd to 10th are the same with the 2nd fingerprint recording method.
Deleting the fingerprint, and the LED indicator light status instruction
Long press the sensor for 10 seconds till the red indicator light remains on, for this moment, use any one of the two  administrator fingerprints can delete all the fingerprints. When the non-administrator fingerprint press the sensor, the red indicator light will flash and report errors.
Note:
Fingerprint deleting function is delete all the fingerprints, you can't operate on a single fingerprint.

Lock:
When the product is unlock, press the lock beam to lock the product.
Unlock:
When the product is locked, enter fingerprint. If use the right fingerprint, the green indicator short flash and the product is unlock. If use the wrong fingerprint, the red indicator short flash.

Low voltage
When the voltage ≤3.5V, the red indicator flash fast for 15s. If keep in the status of low batter, it will alarming per minute.

Charge
The red indicator and green indicator will flash alternatively during charging. Lights off when fully charged.

Specifications:
Support 360 degree angel fingerprint recognize
Resolution: 508DPI
ESD: +/-12kV air, +/-8kV contact
FRR: <1%
FAR: <0.002%
Recognize time: <300mS

P3 Fingerprint Padlock Power Consumption:
Working current: 180MA
Motor less operating current: 3MA
Standby current: 16uA
The product has the features of low power consumption and long standby time. With 1 piece 300MAH lithium polymer battery, the longest standby time can last for 2 years. Maximum number of unlocks up to 2,500. The product can be unlock under emergency situation---It can be unlocked by fingerprint directly when charging.

Here to buy:
Anytek Official Website: Anytekplus.com






Tuesday, November 22, 2016

SOOCOO New Arrivals - S100/C100 4K Action Camera With Gyro and GPS

SOOCOO C100/S100 Action Camera 4K Wifi Built-in Gyro with GPS Extension



 4K VIDEO/20MP PHOTO
Stunning 4K(2008*2160@24fps) video and 20MP photos,in Single, Slow Motion and Time Lapse modes  


GPS Extension(GPS Model not include)
Captures the location where your photos and videos are taken


Advanced Video Stabilization
SOOCOO S100 action camera built-in Gyro chip can capture stunningly smooth video handheld,mounted to your favorite gear, and more


Waterproof
Durable by design, SOOCOO C100 Action Camera is waterproof to 99ft (30m) with a housing

Adjustable Viewing angles(70/110/140/170 Degrees for choose)



Sports camera Exclusivity Light Painting function,Record the perfect picture.





Here to buy S100/C100 Action Camera



SOOCOO C100/S100 Action Camera Specification:

  • DSP:    NTK96660
  • GPS Extension:   Yes (GPS Model not include)
  • Image Sensor:    IMX 078(12M)
  • Video Resolution:  4K@24fps (2880X2160),2560X1440 30fps,1920X1080 60fps,1280X720 120fps,640X480 240fps
  • Image Resolution:    20M/12M/8M/5M/2M
  • Lens:        7 Glass Lens    
  • LCD Display:    2.0 inch HD Screen
  • Extended Memory:    128G(Update Firmware: S20160530)
  • Image File Format:    JPG
  • Video File Format:    MP4
  • Exposure:    Automatic    
  • ISO:    Automatic/100/200/400
  • Interface Type:        USB/HDMI
  • Language:    English/French/German/Spanish/Italian/Portuguese/Simplied Chinese/Japanese/Traditional Chinese/ Russian/Korean/Polish/Swedish
  • Battery Type/Battery capacity:     3.7V   1050mAh li-ion (Longest recording time MAX 70 Min)
  • DDR:    1GB DDR3
  • NAND Flash:    Build-in
  • Speaker:    Build-in
  • MIC:    Build-in
  • Waterproof depth:    Waterproof 30m
  • Built-in WIFI:    Yes
  • Photograph:    Yes
  • Camera angle:    170
  • Storage compression mode:    H.264
  • Motion detection:    YES
  • Loop-record:    Yes,3 minutes/5minute/10minute/off
  • Slow Motion Video: Yes
  • Time-lapse Record: Yes
  • Recording function:    YES
  • Intelligent detection shutdown:    YES
  • Photograph resolution:    MAX 16M
  • AV:    YES
  • Anti-Shake:    YES
  • Gyro:        Yes, Built-in Gyroscope chip
  • Camera Weight:    62g
  • Camera Dimension:    59*41*32mm




Thursday, July 7, 2016

SOOCOO C30 Firmware Update





SOOCOO C30 V1.0 and V2.0 Action Camera Firmware Upgrade Instructions:



1. You will be able to use max 32Gb memory card for firmware upgrade. Format it (FAT32) before use.

2. Empty card can be inserted into your camera. Connect the camera to PC with USB cable.

3. Start upgrade by copying 'FW96660A.bin' and 'FWHT108M.bin' files to the root of the card.

4. Turn the camera off.

5. Unplug USB from PC.

6. Note: Do not try to rename or modify firmware files. It will 'brick' your camera and can lead to its total malfunction.

7. Reconnect the camera to PC. Firmware upgrade will start automatically. Wait until finished.

8. Delete 'FW96660A.bin' and 'FWHT108M.bin' files from the card.

9. Disconnect the camera.



Enjoy updated SOOCOO C30 camera!



---*** If you have any questions, please email us. ***---



Thank you!



Michael



Contact US: service@soocoo.cc

Official Website: http://www.soocoo.cc